Archives

  • 2026-11
  • 2026-10
  • 2026-09
  • 2026-08
  • 2026-07
  • 2026-06
  • 2026-05
  • 2026-04
  • 2026-03
  • 2026-02
  • 2026-01
  • Cy3 Rabbit Anti-Goat IgG (H+L) Antibody: Technical Workflow

    2026-04-27

    Cy3 Rabbit Anti-Goat IgG (H+L) Antibody: Technical Workflow Guide

    What This Product Solves

    The Cy3 Rabbit Anti-Goat IgG (H+L) Antibody (SKU K1215) addresses the need for reliable, high-sensitivity detection of goat IgG in various immunodetection workflows. As a Cy3-conjugated secondary antibody, it enables quantitative and qualitative assessment of targets in immunocytochemistry (ICC/IF), immunohistochemistry (IHC), flow cytometry, and ELISA. The product is affinity-purified to minimize non-specific background, and the Cy3 fluorophore offers excitation/emission maxima at 552/565 nm, suitable for most standard fluorescence imaging systems. This reagent is optimized for signal amplification in immunodetection, particularly when low-abundance targets or challenging tissue contexts demand increased sensitivity (source: internal_article).

    Protocol Parameters

    • assay: Storage temperature | value_with_unit: 4°C (short term, ≤2 weeks); -20°C (long term) | applicability: All immunodetection workflows | rationale: Preserves antibody stability and Cy3 fluorescence; avoid repeated freeze-thaw cycles | source_type: product_spec
    • assay: Working concentration | value_with_unit: 1 mg/mL (as supplied); recommended 1–10 μg/mL for ICC/IF, IHC, flow | applicability: Optimize within assay—start at mid-range | rationale: Ensures adequate signal while minimizing background; titration may be necessary | source_type: product_spec (stock), workflow_recommendation (dilution)
    • assay: Light protection | value_with_unit: Use amber tubes and minimize light exposure | applicability: All fluorescence-based assays | rationale: Prevents Cy3 photobleaching and loss of signal | source_type: product_spec

    Workflow Setup and QC Checklist

    For reproducible results using the Cy3 Rabbit Anti-Goat IgG (H+L) Antibody, follow these workflow guidelines:

    • Aliquot upon receipt: Divide the antibody into single-use aliquots to prevent freeze-thaw cycles that can degrade performance.
    • Blocking step: Use 1% BSA or appropriate blocking buffer to reduce non-specific binding during incubation with the secondary antibody (source: internal_article).
    • Incubation: Incubate the diluted secondary antibody for 30–60 minutes at room temperature or as optimized for your protocol.
    • Wash thoroughly: Multiple PBS washes (at least 3×, 5 min each) post-incubation are critical to remove unbound antibody and reduce background.
    • QC control slides: Always include a no-primary control to monitor for non-specific secondary antibody binding.
    • Imaging settings: Confirm that the microscope/filter set is compatible with Cy3 (excitation 552 nm, emission 565 nm).
    • Documentation: Record lot numbers, storage dates, and experimental details for traceability and troubleshooting.

    Common Failure Modes and Fixes

    • High background signal: Likely due to insufficient blocking, over-concentrated antibody, or inadequate washing. Increase blocking reagent concentration, further dilute the secondary antibody, and extend wash steps.
    • Weak or absent signal: Causes may include photobleaching (exposure to ambient light), expired antibody, or incompatible imaging filters. Protect antibody from light, verify filter sets, and check antibody storage conditions.
    • Non-specific staining: Confirm that the primary antibody is goat-derived and that species cross-reactivity is not an issue. Use proper negative controls and validate specificity in your system.
    • Precipitate or cloudiness in vial: Indicates protein aggregation, often from repeated freeze-thaw or contamination. Discard affected aliquots and use fresh, properly stored material.

    Scope and Limitations

    This Cy3-conjugated secondary antibody is validated for use with goat IgG primaries in fluorescence-based detection, including ICC, IF, IHC (frozen and paraffin-embedded), flow cytometry, and ELISA (internal_article). It is not suitable for detection of non-goat primary antibodies or applications outside standard immunodetection. Cross-species reactivity is not supported; always match the host species of the primary antibody to the specificity of the secondary. For novel or high-throughput applications, preliminary titration and specificity testing are recommended. Do not use this reagent for diagnostic or therapeutic purposes unless explicitly validated for such workflows.

    Conclusion

    The Cy3 Rabbit Anti-Goat IgG (H+L) Antibody (SKU K1215) provides a reliable, efficient solution for signal amplification in immunodetection workflows when used according to validated protocols. Its affinity-purified, Cy3-conjugated format supports sensitive detection with minimal background in ICC, IHC, flow cytometry, and ELISA. For full product specifications, refer to the official Cy3 Rabbit Anti-Goat IgG (H+L) Antibody page at APExBIO.